CORRELATIONS TO PREDICT THERMAL PERFORMANCE AFFECTED BY WORKING FLUID'S PROPERTIES OF VERTICAL AND HORIZONTAL CLOSED-LOOP PULSATING HEAT PIPE

Abstract

Objectives of this paper are to investigate the effects of dimensionless numbers on the thermal performance, and to establish correlations to predict the thermal performance of the vertical and a horizontal closed-loop pulsating heat pipe. The heat pipes were made of long copper capillary tubes with 26 meandering turns and both the ends were connected together to form a loop. R123, R141b, acetone, ethanol, and water were chosen as variable working fluids with a constant filling ratio of 50% by total volume. The inlet temperature of the heating medium and the adiabatic section temperature were constantly controlled and maintained at 80 °C and 50 °C, respectively. The thermal performance was represented in terms of the Kutateladze number. It can be concluded that when the Prandtl number of the liquid working fluid, as well as the Karman number, increases, the thermal performance increases. On the other hand, when the Bond number, the Jacob number, and the Aspect ratio increase, the thermal performance decreases. These effects of the dimensionless numbers on the thermal performance are valid for both the heat pipes, except in the case of Bond number which has no effect on the thermal performance as far as the horizontal heat pipe is concerned. Moreover, correlations to predict thermal performance have been successfully established.

Keywords

Dates

  • Submission Date2014-05-03
  • Revision Date2014-06-29
  • Acceptance Date2014-08-03
  • Online Date2014-09-06

DOI Reference

10.2298/TSCI140503105S

References

  1. Akachi, H. et al., Pulsating Heat Pipes, Proceedings, 5th Intl. Heat Pipe Symp., Melbourne, Australia, 1996, pp. 208-217.
  2. Maezawa, S. et al., Thermal Performance of Capillary Tube Thermosyphon, Proceedings, 9th Intl. Heat Pipe Conf., Albuquerque, USA, 1995, pp. 791-795.
  3. Xu, J. L. et al., High Speed Flow Visualization of a Closed Loop Pulsating Heat Pipe, Heat Mass Transfer, 48 (2005), pp. 3338-3351.
  4. Soponpongpipat, N. et al., Investigation of the Startup Condition of a Closed Loop Oscillating Heat Pipe, Heat Transfer Eng., 30 (2009), 8, pp. 626-642.
  5. Charoensawan, P. et al., Closed Loop Pulsating Heat Pipes - Part A: Parametric Experimental Investigations, Appl. Therm. Eng., 23 (2003), 16, pp. 2009-2020.
  6. Khandekar, S. et al., Closed Loop Pulsating Heat Pipes - Part B: Visualization and Semi- Empirical Modeling, Appl. Therm. Eng., 23 (2003), 16, pp. 2021-2033. ]7] Zhang, X. M., Experimental Study of a Pulsating Heat Pipe using FC-77, Ethanol, and Water as Working Fluids, Exp. Heat Transfer, 17 (2004), 1, pp. 77-77.
  7. Charoensawan, P., Terdtoon, P., Thermal Performance of Horizontal Closed-Loop Oscillating Heat Pipe, Appl. Therm. Eng., 28 (2008), 5-6, pp. 460-466.
  8. Sakulchangsatjatai, P. et al., Operation Modeling of Closed-End and Closed-Loop Oscillating Heat Pipes at Normal Operating Condition, Appl. Therm. Eng., 24 (2004), 7, pp. 995-1008.
  9. Kammuang-lue, N. et al., Effect of Working Fluids on Thermal Effectiveness of Closed-Loop Pulsating Heat Pipe Applied in Ice Storage System, Proceedings, 8th Intl. Heat Pipe Symp., Kumamoto, Japan, 2006, pp. 323-328.
  10. Kammuang-lue, N. et al., Effect of Working Fluids on Thermal Characteristic of a Closed-Loop Pulsating Heat Pipe Heat Exchanger: A Case of Three Heat Dissipating Devices, Proceedings, IEEE 14th Electronics Packaging Technology Conf., Singapore, 2012, pp. 142-147.
  11. Charoensawan, P. et al., Effect of Evaporator Section Lengths, Number of Turns and Working Fluid on Internal Flow Patterns of a Vertical Closed-Loop Oscillating Heat Pipe, Proceedings, 7th Intl. Heat Pipe Symp., Jeju, Korea, 2003, pp. 360-367.
  12. Khandekar, S. et al., Understanding Operational Regimes of Closed Loop Pulsating Heat Pipes: An Experimental Study, Appl. Therm. Eng., 23 (2003), 6, pp. 707-719.
  13. Charoensawan, P. et al., Effect of Inclination Angles, Filling Ratios and Total Lengths on Heat Transfer Characteristics of a Closed-Loop Oscillating Heat Pipe, Proceedings, 6th Intl. Heat Pipe Symp., Chiang Mai, Thailand, 2000, pp. 421-430.
  14. Zhang, Y., Faghri, A., Heat Transfer in a Pulsating Heat Pipe with Open End, Heat Mass Transfer, 45 (2002), 4, pp. 755-764.
  15. Groll, M., Khandekar, S., Pulsating Heat Pipes: Progress and Prospects, Proceedings, Intl. Conf. on Energy and the Environment, Shanghai, China, 2003, Vol. 1, pp. 723-730.
  16. Shafii, M. B. et al., Thermal Modeling of Unlooped and Looped Pulsating Heat Pipes, ASME J. Heat Transfer, 123 (2001), pp. 1159-1171.
  17. Shafii, M. B. et al., Analysis of Heat Transfer in Unlooped and Looped Pulsating Heat Pipes, Intl. J. Numerical Methods for Heat and Fluid Flow, 12 (2002), 5, pp. 585-609.
  18. Sriwiset, C. et al., Evaluation of Optimum Turn Number for Closed-Loop Pulsating Heat Pipe at Normal Operation, Proceedings, 5th Intl. Conf. on Science, Technology and Innovation for Sustainable Well-Being, Luang Prabang, Lao PDR, 2013, pp. MME06 1-5.