ENERGY EFFICIENCY IMPROVEMENT BY GEAR SHIFTING OPTIMIZATION

Abstract

Many studies have proved that elements of driver's behavior related to gear selection have considerable influence on the fuel consumption. Optimal gear shifting is a complex task, especially for inexperienced drivers. This paper presents an implemented idea for gear shifting optimization with the aim of fuel consumption minimization with more efficient engine working regimes. Optimized gear shifting enables the best possible relation between vehicle motion regimes and engine working regimes. New theoretical-experimental approach has been developed using On-Board Diagnostic technology which so far has not been used for this purpose. The matrix of driving modes according to which tests were performed is obtained and special data acquisition system and analysis process have been developed. Functional relations between experimental test modes and adequate engine working parameters have been obtained and all necessary operations have been conducted to enable their use as inputs for the designed algorithm. The created Model has been tested in real exploitation conditions on passenger car with Otto fuel injection engine and On-Board Diagnostic connection without any changes on it. The conducted tests have shown that the presented Model has significantly positive effects on fuel consumption which is an important ecological aspect. Further development and testing of the Model allows implementation in wide range of motor vehicles with various types of internal combustion engines.

Keywords

Dates

  • Submission Date2012-01-29
  • Revision Date2012-02-13
  • Acceptance Date2012-02-14

DOI Reference

10.2298/TSCI120129035B

References

  1. Shinar, D., Meir, M., Ben-Shoham, I., How automatic is manual gear shifting?, Human Factors, 40 (1999), 4, pp. 647-654
  2. Groeger, J.A., Clegg, B.A., Automaticity and driving: Time to change gear conceptually, in: Traffic and transport psychology: Theory and application (Ed. V.E. Carbonell and T. Rothengatter), Pergamon Press, Oxford, 1997
  3. De Vlieger, I., De Keukeleere, D., Kretzschmar, J.G., Environmental effects of driving behaviour and congestion related to passenger cars, Atmospheric Environment, 34 (2000), 27, pp. 4649- 4655
  4. Hooker, J.N., Optimal driving for single-vehicle fuel economy, Transportation Research Part A, 22 (1988), 3, pp. 183-201
  5. Van Mierlo, J., Maggetto, G., Van de Burgwal, E., Gense, R., Driving style and traffic measures - influence on vehicle emissions and fuel consumption, Proc. IMechE, Part D: Journal of Automobile Engineering, 218 (2004), N1, pp. 43-50
  6. ***, National Research Council, Automobile Fuel Economy - How Far Should We Go?, National Academy Press, Washington D.C., 1992.
  7. Schindler, K.P., Fuel Savings by Car. Presented at the Strategies for Promoting Fuel Saving On- Board Technologies - OPET Workshop, Brussels, Belgium, 2003
  8. Van der Voort, M., Dougherty, S. M., Van Maarseveen, M., A prototype fuel-efficiency support tool, Transportation Research Part D, 9 (2001), 4, pp. 279-296
  9. Decicco, J., Ross, M., Recent advances in automotive technology and the cost-effectiveness of fuel economy improvement, Transportation Research Part C, 1 (1996), 2, pp. 79-96
  10. Vanke, J., Techniques for Influencing Driving - The Driver's View, Presented at the ECMT Expert Workshop on In-Car Technology, Delft, Netherlands, 1996
  11. ***, Gear Shift Indicator System - Toyota Technical Documentation, Toyota Motor Corporation, Toyota City, 2009
  12. Experts from Germany, Proposal for Draft Amendment to the 05 Series of Amendments to Regulation No. 83 (Emissions of M1 and N1 Categories of Vehicles), to: Economic Commission for Europe, Inland Transport Committee, World Forum for Harmonization of Vehicle Regulation (WP.29), Working Party on Pollution and Energy (49th GRPE), 2004
  13. Blagojevic, I., Vorotovic, G., The Possibilities for Acquisition and Usage of Data Concerning a Large Number of Vehicles Functioning, in Real Terms of Exploitation Using OBD Technology, Conference on Virtual Product Development in Automotive Engineering, Graz, Austria, 2004, pp. 28-29
Volume 17, Issue 1, Pages91 -105