INVESTIGATIONS OF EFFECTS OF PILOT INJECTION WITH CHANGE IN LEVEL OF COMPRESSION RATIO IN A COMMON RAIL DIESEL ENGINE

Abstract

These day diesel engines are gaining lots of attention as prime movers for various source of transportation. It offers better drive ability, very good low end torque and importantly the lower CO2 emission. Diesel engines are bridging the gap between gasoline and diesel engines. Better noise vibration and harshness levels of gasoline engine are realized to great extent in diesel engine, thanks to common rail direct injection system. Common rail injection system is now well known entity. Its unique advantage is flexible in operation. In common rail injection system, number of injection prior and after main injection at different injection pressure is possible. Due to multiple injections, gain in emission reduction as well as noise has been already experienced and demonstrated by researcher in the past. However, stringent emission norms for diesel engine equipped vehicle demands for further lower emission of oxides of nitrogen (NOx) and particulate matter (PM). n the present paper, authors attempted to study the effect of multiple injections in combination with two level of compression ratio. The aim was to study the combustion behavior with the reduced compression ratio which is going to be tried out as low temperature combustion concept in near future. The results were compared with the current level of compression ratio. Experiments were carried out in 2.2L cubic capacity engine with two levels of compression ratios. Pilot injection separation and quantities were varied keeping the main injection, rail pressure, boost pressure and EGR rate constant. Cylinder pressure traces and gross heat release rates were measured and analyzed to understand the combustion behavior.

Dates

  • Submission Date2012-01-05
  • Revision Date2012-07-30
  • Acceptance Date2012-08-20

DOI Reference

10.2298/TSCI120105154G

References

  1. Keiichi, Okude , et. al., Effects of multiple injections on Diesel Emission and combustion Characteristics, Transactions of Society of Automotive Engineers, SAE Paper 2007-01-4178, 2007
  2. Marko, Jeftić, et. al., Effects of Post injection application with late partially premixed combustion on Power production and diesel exhaust gas conditioning, Research article.
  3. D. A., Pierpont, D. T., Montgomery, and R., D., Reitz, Reducing Particulate and NOx Using Multiple Injections and EGR in a D.I. Diesel, Transactions of Society of Automotive Engineers, SAE Paper 950217, 1995
  4. Paolo, Carlucci, Antonio ,Ficarella and Domenico ,Laforgia, Effect of pilot Injection Parameters on Combustion for common rail Diesel engines, Transactions of Society of Automotive Engineers, SAE Paper 2003-01-0700, 2003
  5. Usman, Asad, et.al, Fuel Injection Strategies to Improve emissions and efficiency of high Compression ratio diesel engine, Transactions of Society of Automotive Engineers, SAE paper 2008-01-2472, 2008
  6. Gavin , Dober, et.al., The impact of injection strategies on emissions reduction and power output of future diesel engines, Transactions of Society of Auto motive Engineers, SAE paper 2008-01-0941; 2008
  7. Dr., Ichiro, Sakata, et. al., A new combustion concept for passenger car diesel engines based on a low compression ratio, 15 Aachener Kolloquium Fahrzeug- und Motorentechnik, 2006, pp 293-314
  8. Radivoje, B. Pesic, Sasa, T., Milojevic and Stevan, P., Veinovic, Benefits and challenges of variable Compression ratio diesel engine, Thermal Science: Vol. 14, (2010) No. 4, pp. 1063-1073
  9. Thirunavukkarasu , Ganpathy, Rakesh, Parkash, Gakkhar and Krishnan Murugesan, An Analytical and Experimental study of performance of Jatropha biodiesel engine, Thermal Science: Vol. 13 (2009), No. 3, pp. 69-82
  10. Miroljub, V., Tomic, et. al., A quick simplified approach to the evaluation of combustion rate from an Internal combustion engine indicator diagram, Thermal Science: Vol. 12 (2008), No. 1, pp. 85-102
  11. Dr., Peter, L., Herzog, Combustion development directions from HSDI diesel engines, Symposium of International automotive technology, 2005, pp. 31-40
  12. Ashok, A., Dhale, Gajanan, K., Awari and Mahendra, P., Singh, Analysis of Internal combustion engine with a new concept of porous medium combustion for future clean engine, Thermal Science: Vol. 14 (2010), No. 4, pp. 943-956
  13. John, B., Heywood, Internal combustion engine fundamentals, McGraw-Hill Inc.USA, 1988.
Volume 17, Issue 1, Pages71 -80