DEVELOPMENT OF A SIMULATION MODEL FOR COMPRESSION IGNITION ENGINE RUNNING WITH IGNITION IMPROVED BLEND

Abstract

The present work describes the thermodynamic and heat transfer models used in a computer program which simulates the diesel fuel and ignition improver blend to predict the combustion and emission characteristics of a direct injection compression ignition engine fuelled with ignition improver blend using classical two zone approach. One zone consists of pure air called non burning zone and other zone consist of fuel and combustion products called burning zone. First law of thermodynamics and state equations are applied in each of the two zones to yield cylinder temperatures and cylinder pressure histories. Using the two zone combustion model the combustion parameters and the chemical equilibrium composition were determined. To validate the model an experimental investigation has been conducted on a single cylinder direct injection diesel engine fuelled with 12% by volume of 2- ethoxy ethanol blend with diesel fuel. Addition of ignition improver blend to diesel fuel decreases the exhaust smoke and increases the thermal efficiency for the power outputs. It was observed that there is a good agreement between simulated and experimental results and the proposed model requires low computational time for a complete run.

Dates

  • Submission Date2010-07-17
  • Revision Date2011-01-26
  • Acceptance Date2011-02-05

DOI Reference

10.2298/TSCI100717043S

References

  1. Shroff, H. D., Hodgetts, D., Simulation and Optimization of Thermodynamic Processes of Diesel Engine, SAE 740194, 1974
  2. Ganesan, V., Computer simulation of Compression-Ignition engine processes, University Press (India) Ltd., Hyderabad, India, 2000
  3. Heywood, J. B., International Combustion Engine Fundamentals, McGraw hill Book Company, New York, 1988
  4. Annand, W. J. D., Heat Transfer in the Cylinders of Reciprocating Internal Combustion Engines, Proceedings Instn Mech Engrs., 177, (1963), 36, pp. 973-996
  5. Chow, A., Wyszynski, M. L., Thermodynamic modeling of complete engine systems - a review, Proceedings Instn Mech Engrs., 213, (1999)
  6. Ericson, C., et al., Modeling diesel engine combustion and NOx formation for model based control and simulation of engine and exhaust after treatment systems, SAE 2006-01-0687
  7. Rakopoulos, C. D., et al., Validation and sensitivity analysis of a two zone Diesel engine model for combustion and emissions prediction, Energy Conversion and management, 45, (2004), pp.1471-1495
  8. Merker, G. P., Hohlbaum, B., Rauscher, M., Two-Zone model for calculation of Nitrogen Oxide formation in Direct-Injection diesel engines, SAE 932454, 1993
  9. Hountalas, D. T., Papagiannakis, R.G., Development of a simulation model for direct injection dual fuel diesel-natural gas engines, SAE 2000-01-0286, 2000
  10. Ishida, M., et al., Combustion analysis by Two-Zone model in a diesel engine, International Symposium, Comodia, 1994
  11. Ramachandran, S., Rapid thermodynamic simulation model of an Internal Combustion Engine on alternate fuels, Proceedings of the International Multiconference of Engineers and computer Scientists, HongKong, March 18-20, 2009
  12. McCartan C. D., et al., Computer simulation of the performance of a 1.9 Litre Direct Injection Diesel Engine, SAE 2002-01-0070, 2002
  13. Ganapathy, T., et al., An analytical and experimental study of performance on Jatropha biodiesel engine, Journal Thermal Science, 13, (2009), 3, pp. 69-82
  14. Tamilporai, P., et al., Simulation and Analysis of Combustion and Heat Transfer in Low Heat Rejection Diesel Engine Using Two Zone Combustion Model and Different Heat Transfer Models, SAE 2003-01-1067, 2003
  15. Whitehouse, N. D., Benson, R. S., Internal combustion engines, Pergamon press, England, 1979.
  16. Colin R. Ferguson., Internal combustion engines, Applied Thermo sciences, John Wiley & sons, Inc. Newyork, 1986
  17. Boussouara, K., Kadja, M., Empirical soot formation and oxidation model, Journal Thermal Science, 13, (2009), 3, pp. 35-46
Volume 15, Issue 4, Pages1131 -1144