ELASTIC-PLASTIC TRANSITION STRESSES IN A THIN ROTATING DISC WITH RIGID INCLUSION BY INFINITESIMAL DEFORMATION UNDER STEADY-STATE TEMPERATURE

Abstract

Stresses for the elastic-plastic transition and fully plastic state have been derived for a thin rotating disc with rigid shaft at different temperatures and results have been discussed and depicted graphically. It has been observed that at room temperature rotating disc made of compressible material and of smaller radii ratio yields at the internal surface at a higher angular speed as compared to rotating disc made of incompressible material. With the introduction of thermal effect rotating disc yields at the outer surface at a lesser angular speed as compared to rotating disc at room temperature. The circumferential stress is maximum at the outer surface of the rotating disc with further increases with the increase in temperature. It means that angular speed of the rotating disc is less than that of the temperature-loaded disc in the fully plastic case.

Dates

  • Submission Date2009-01-31
  • Revision Date2009-05-23
  • Acceptance Date2009-06-22

DOI Reference

10.2298/TSCI1001209P

References

  1. Timoshenko, S. P., Goodier, J. N., Theory of Elasticity, Mc Graw- Hill, New York, USA, 1970
  2. Chakrabarty, J., Theory of Plasticity, McGraw- Hill, New York, USA, 1987
  3. Heyman, J., Plastic Design of Rotating Discs, Proc. Inst. Mech. Engrs., 172 (1958), 3, pp. 531-546
  4. Johnson, W., Mellor, P. B., Plasticity for Mechanical Engineer's, D. Van-Nostrand, London, 1962
  5. Parmaksigoglu, C., Guven, U., Plastic Stress Distribution in a Rotating Disc with Rigid Inclusion under a Radial Temperature Gradient, Mech. Struct. and Mach., 26 (1998), 1, pp. 9-20
  6. Seth, B. R., Transition Theory of Elastic-Plastic Deformation, Creep and Relaxation, Nature, 195 (1962), 3, pp. 896-897
  7. Seth, B.R., Measure Concept in Mechanics, Int. J. Non-Linear Mech., I (1966), 2, pp. 35-40
  8. Pankaj, T., Elastic-Plastic Transition Stresses in a Transversely Isotropic Thick-Walled Cylinder Subjected to Internal Pressure and Steady-State Temperature, Thermal Science, 13 (2009), 4, pp 107-118
  9. Pankaj, T., Sonia, R. B., Elastic-Plastic Transition in a Thin Rotating Disc with Inclusion, Intl J. Mathematical, Physical and Engineering Sci. 2 (2008), 3, pp. 150-154
  10. Pankaj, T., Sonia, R. B., Creep Transition in a Thin Rotating Disc Having Variable Density with Inclusion, Int. J. Math. Phys. Eng. Sci. 2 (2008), 3, pp.140-149
  11. Pankaj, T., Gupta, S. K.,Thermo Elastic-Plastic Transition in a Thin Rotating Disc with Inclusion, Thermal Science, 11 (2007), 1, pp. 103-118
  12. Pankaj, T., Gupta, S. K., Creep Transition in a Thin Rotating Disc with Rigid Inclusion Defence, Sci. Journal, India, 57 (2007), 2, pp. 185-195
  13. Pankaj, T., Gupta, S. K., Creep Transition in an Isotropic Disc Having Variable Thickness Subjected to Internal Pressure, Proceeding, National Academy of Science, India, Section- A, 78 (2008), part I, pp. 57-66
  14. Pankaj, T., Elastic-Plastic Transition in a Thin Rotating Disc Having Variable Density with Inclusion, Structural Integrity and Life, Serbia, 9 (2009), 3, pp. 171-179
  15. Pankaj, T., Elastic-Plastic Transition Stresses in an Isotropic Disc Having Variable Thickness Subjected to Internal Pressure, International Journal of Physical Science, 4 (2009), 5, pp. 336-342
  16. Parkus, H., Thermo-Elasticity, Springer-Verlag, Wien, New York, USA, 1976
Volume 14, Issue 1, Pages209 -219